des SBC S-Bus kompatibel. Symptom Bei Neu-Inbetriebnahme von Romutec S-Bus Kopplern SBZK1000 oder nach Update der PCD-Firmware funktioniert die Kommunikation zwischen Saia PCD®/PCS und Romutec Koppler nicht (mehr). Ursache Der neue Secure Data Mode (SData-Mode) des S-Bus wird zur Zeit von Romutec nicht unterstützt. S-Bus Telegramme im SData-Mode führen zur Fehlfunktion [...] verwendet werden, solange Romutec den SData-Mode nicht unterstützt. Stattdessen wird die manuelle Einstellung des normalen S-Bus Data-Mode im SBZK1000 empfohlen. Details zur Einstellung des SBZK finden Sie in
Netzwerks (wenn es IP- Kommunikation ist, benutzen Sie bitte Wireshark, Informationen dazu unter FAQ #100569) Falls die Kommunikation mit dem S-Bus Treiber SComm in Zusammenhang steht (z.B. PG5 zu PCD [...] . PCMCIA card with 2 serial COM Ports (RS-232) suitable for S-Bus (FAQ #100764) Serial S-Bus is still very often in use for [...] -232 adapters may be a solution, but there is no guaranty that a specific adapter will work with SBC S-Bus properly. The EXSYS PCMCIA card EX-1352 with 2 serial RS-232 ports has been sucessfully
e.g. be Ether-S-Bus. How can I realize a gateway from BACnet to LON with PCD systems? The currently only solution is the realisation with two systems, which could e.g. be connected with Ether-S-Bus. Why it’s not possible to make the binding with the LonMaker to a PCS1? (FAQ #101132) If a PCS1 does use at the same time a serial communication with > 9’600 baud and the user wants to make a binding with the LonMaker then it’s possible that the binding will not succeed and on the LonMaker there is an error message
. Why does my RS-232 S-Bus communication not work with the PCD2.F2xx0 and PCD3.F2xx module? (FAQ #101775) The RS-232 S-Bus [...] V020) it may be, that the S-Bus communication over converters (like modem or optical converters) to other devices does not work. The S-Bus communication works fine, if no converters are used in between. Also other communications protocols then S-Bus like "Mode C, Modbus" works fine on the PCD2.F2xx0 and PCD3.F2xx module (with and without converters in between). On the print screen below
the electrical systems (Saia PCD1.M0160E0) is a Function PCD that can be used immediately in the default setting without any programming. Energy meters connected via S-Bus and H104SE gateway modules for [...] PCD1 / _Firmware Classic Why the RS-485 S-Bus [...] possible that the some of the S-Bus telegrams transferred from the PCD S-Bus master to the S-Bus slaves over RS485 are malformed, and the S-Bus slave does reject the request from the master. This could
2.F540). PCD2 / _Firmware Classic Why the RS-485 S-Bus [...] possible that the some of the S-Bus telegrams transferred from the PCD S-Bus master to the S-Bus slaves over RS485 are malformed, and the S-Bus slave does reject the request from the master. This could lead to the situation that for example the PCD S-Bus master don’t receive actual values from E-Line RIO’s or that the program download of a PCD program from the PC to a Slave PCD which is located behind
. PCD2 / _Firmware Classic Why the RS-485 S-Bus [...] possible that the some of the S-Bus telegrams transferred from the PCD S-Bus master to the S-Bus slaves over RS485 are malformed, and the S-Bus slave does reject the request from the master. This could lead to the situation that for example the PCD S-Bus master don’t receive actual values from E-Line RIO’s or that the program download of a PCD program from the PC to a Slave PCD which is located behind
F1. PCD2 / _Firmware Classic Why the RS-485 S-Bus [...] possible that the some of the S-Bus telegrams transferred from the PCD S-Bus master to the S-Bus slaves over RS485 are malformed, and the S-Bus slave does reject the request from the master. This could lead to the situation that for example the PCD S-Bus master don’t receive actual values from E-Line RIO’s or that the program download of a PCD program from the PC to a Slave PCD which is located behind
communication errors when connecting a PCD/PCS in "Secure S-Bus Data Mode"? (FAQ #101180) In case a "non Saia PCD® COSinus" PCD or PCS1 system is connected with "Secure S-Bus Data mode" (e.g. over a serial cable or over modem) from time to time a telegram is not answered correctly. Symptom A PCD or a PCS connected with another system (e.g. PC or another PCD system) using the "Secure S-Bus Data mode" does not answer a telegram from time to time. This can e.g. be seen by a red LED on transmit or receive FBoxes
. PCD2 / _Firmware Classic Why the RS-485 S-Bus [...] possible that the some of the S-Bus telegrams transferred from the PCD S-Bus master to the S-Bus slaves over RS485 are malformed, and the S-Bus slave does reject the request from the master. This could lead to the situation that for example the PCD S-Bus master don’t receive actual values from E-Line RIO’s or that the program download of a PCD program from the PC to a Slave PCD which is located behind
