.ch. On a PCD3.M6860 it’s possible to use BACnet on the Ethernet port ETH1 and/or on ETH2? (FAQ #102031) Yes it’s possible to use BACnet on both ports ETH1 or ETH2 of the PCD3.M6860. In PG5 it’s possible to activate at the same time BACnet on ETH1 and ETH2 but we strongly recommend to use/activate BACnet only on one of the two Ethernet ports to avoid a bad behavior on BACnet. The activation and selection of the used Ethernet port for BACnet communication on the PCD3.M6860 is done in PG5 2.2 or PG5 2.3
.ch. On a PCD3.M6860 it’s possible to use BACnet on the Ethernet port ETH1 and/or on ETH2? (FAQ #102031) Yes it’s possible to use BACnet on both ports ETH1 or ETH2 of the PCD3.M6860. In PG5 it’s possible to activate at the same time BACnet on ETH1 and ETH2 but we strongly recommend to use/activate BACnet only on one of the two Ethernet ports to avoid a bad behavior on BACnet. The activation and selection of the used Ethernet port for BACnet communication on the PCD3.M6860 is done in PG5 2.2 or PG5 2.3
.ch. On a PCD3.M6860 it’s possible to use BACnet on the Ethernet port ETH1 and/or on ETH2? (FAQ #102031) Yes it’s possible to use BACnet on both ports ETH1 or ETH2 of the PCD3.M6860. In PG5 it’s possible to activate at the same time BACnet on ETH1 and ETH2 but we strongly recommend to use/activate BACnet only on one of the two Ethernet ports to avoid a bad behavior on BACnet. The activation and selection of the used Ethernet port for BACnet communication on the PCD3.M6860 is done in PG5 2.2 or PG5 2.3
Modbus driver is implemented in the firmware of the PCD1.M2, the PCD2.M5 and all PCD3 controllers. The configuration of the driver is done by FBoxes or in IL. The physical layers supported are RTU, ASCII [...] (default for Modbus) Modbus Client: (PCD3.M3330) IP Address: 172.16.1. 45 Modbus Server: (PCD3.M5540) IP Address: 172.16.1. 46 UID: 33 (Unit Identifier [...] Modbus are automatically installed with PG5 2.0 but need to be licensed. For older PCD systems (such as the PCD2.M170 or the PCD1.M1x5) a pure FBox solution from the company Engiby exists
. 1-ph. M-Bus Interf. 3-ph. M-Bus Interf [...] supply voltage pins 1L/2L and 3N/4N are inverted. This wrong label is present on the schema of the housing and directly on the pins. Problem When a PCD7.T162 produced before week 22 of 2011 [...] functionality is still the same but the 24V DC need to be connected to the pins 3N/4N and the 0V to 1L/2L. Remark Units of PCD7.T162 produced after 11/22 (30.05.2011) are correctly labelled and
. 1-ph. M-Bus Interf. 3-ph. M-Bus Interf [...] supply voltage pins 1L/2L and 3N/4N are inverted. This wrong label is present on the schema of the housing and directly on the pins. Problem When a PCD7.T162 produced before week 22 of 2011 [...] functionality is still the same but the 24V DC need to be connected to the pins 3N/4N and the 0V to 1L/2L. Remark Units of PCD7.T162 produced after 11/22 (30.05.2011) are correctly labelled and
. PG5 2.2 On a PCD3.M6860 it’s possible to use [...] 2 of the PCD3.M6860. In PG5 it’s possible to activate at the same time BACnet on ETH1 and ETH2 but we strongly recommend to use/activate BACnet only on one of the two Ethernet ports to avoid a bad behavior on BACnet. The activation and selection of the used Ethernet port for BACnet communication on the PCD3.M6860 is done in PG5 2.2 or PG5 2.3 in the device configurator. On
. PG5 2.2 On a PCD3.M6860 it’s possible to use [...] 2 of the PCD3.M6860. In PG5 it’s possible to activate at the same time BACnet on ETH1 and ETH2 but we strongly recommend to use/activate BACnet only on one of the two Ethernet ports to avoid a bad behavior on BACnet. The activation and selection of the used Ethernet port for BACnet communication on the PCD3.M6860 is done in PG5 2.2 or PG5 2.3 in the device configurator. On
. PG5 2.2 On a PCD3.M6860 it’s possible to use [...] 2 of the PCD3.M6860. In PG5 it’s possible to activate at the same time BACnet on ETH1 and ETH2 but we strongly recommend to use/activate BACnet only on one of the two Ethernet ports to avoid a bad behavior on BACnet. The activation and selection of the used Ethernet port for BACnet communication on the PCD3.M6860 is done in PG5 2.2 or PG5 2.3 in the device configurator. On
some protective measures. Information about protective measures can be found on the support hp If you need a PCD with cyber security levels SL3+ and based on ANSI ISA 62443 then checkout our PCD3.M6893 (QronoX PCD), this PCD was developed for cybersecure applications. Information's can be found here . [...] with header line N4.3 On the Niagara article, for the Saia-PCD Supervisor version 1.1, check the column with header line N
