speed of the PCD7-L60x-1 Example: If the register has the value: ‘30’ then the maximum speed would be 3 and the minimum speed 0 ‘22’ then the maximum speed would be 2 and the minimum speed 2 -> the [...] . Which inputs values needs the FBox 'Man AO' (L60x-1 Man AO) to control the Y3/Y4/PWMs outputs on a PCD7.L60x-1 controller? (FAQ #101837) [...] FBox family 'RoomControler PCD7_60x V2' does need to have a decimal value without decimal point. (for an output value of 8.3 V the decimal value 83 have to be set) This FBox allows the manual
COSinus FW 1.28.37 was released as maintenance version for the systems: - PCD1.M0xx0/M2xx0, PCD2.M4x60, PCD3.Mxx60, PCD3.M6880 and PCD3.T665/T666/T668 . In June 2017: the COSinus FW 1.28.16 was introduced into production for the systems: - PCD1.M0xx0/M2xx0, PCD2.M4x60, PCD3.Mxx60, PCD3.M6880 and PCD3.T665/T666/T668 . the BACnet and LonIP FW 1.28.16 was put into production [...] the following PCD's with 8 MB onboard firmware memory: PCD1.M0xx0/M2xx0, PCD2.M4x60, PCD3.Mxx60, PCD3.M6880 and PCD3.T665/T666/T668 The table below does show the hardware dependencies in
01 0271 0022 fexible cable Note: If the bautrates isn't greater than 187,5 bautes (for ex. Profi S-Bus with PCD3.M3xx / PCD7.D7xx) you can use other more advantegeous cable, especially [...] 7.T160 D-Sub 9pin on PCD Port 2 on PCD3.M3 and M6 A=RxD /TxD-N green D pin 8 D B=RxD /TxD-P red D/ pin 3 /D Example for the port 3 of the PCD3.M5540 as Serial-S-Bus RS485 connection (Serial-S-Bus) between PCD3.M5540 port 3 (S-Net D-Sub used as RS485 Serial-S-Bus) and PCD2.M5540 port 2 (connector block X3
are connected to PCD3.Mxxx or PCD2.M480 PLC's over Profi S-Bus, the terminal loses the communication after some time and get even frozen. This problem is corrected in the new boot, FW and driver. The PCD8.D81 V 5.09 is needed , the attached files have to be copied in it (see procedure below). It is also necessary to update the PCD3.Mxxx and PCD2.M480 FW with the version PCD3.Mxxx_023.blk / PCD2.M [...] OS do not allow the access to COM-ports in the way which is used for DOS. Use an operating system which is based on DOS (DOS, WIN 3.11, Windows 95 or Windows 98) instead. PCD7.D8 is a
On a Profi S-Bus network when PCD7.D76_ terminals are connected to PCD3.Mxxx or PCD2.M480 PLC's over Profi S-Bus, the terminal loses the communication after some time and get even frozen. This problem is corrected in the new boot, FW and driver. The PCD8.D81 V 5.09 is needed , the attached files have to be copied in it (see procedure below). It is also necessary to update the PCD3.Mxxx and PCD2.M480 FW with the version PCD3.Mxxx_023.blk / PCD2.M480_$27 or newer! Ask the PCD technical support or your representation for it!
COSinus FW 1.24.69 was introduced into production for the systems PCD2.M5xx0, PCD3.Mxxx0. The corresponding BACnet and LonIP firmware is available on the support homepage. In March 2017 the COSinus FW 1.24.67 was introduced into production for the systems PCD2.M5xx0, PCD3.Mxxx0. The corresponding BACnet and LonIP firmware is available on the support homepage. In Mai 2015 the maintenance COSinus FW 1.24.30 was published for the systems PCD1.M0xx0, PCD1.M2xx0, PCD2.M5xx0, PCD3.Mxxx0, PCD3.Mxx60 and PCD7.D4xxxT5F. In February 2015 the COSinus FW 1.24.25 was introduced into
itselfs influences the measurement it has been stated that the precisision is not according to the manual of this PCD7.D290 display (26/841 version 4). The chapters 4.2.3 (Temperature sensor) and 4.2.4 (R.H. sensor) will be adapted accordingly in the next release. 4.2.3 Temperature sensor Temperature sensor used in PCD7.D290 is active and supplies as output a voltage of 10.0 mV/°C; this [...] Product Category HMI Text Terminal PCD7.D290 General
. HMI Editor and PCD3.M_ or PCD2.M480: Wrong characters are display instead of value with Format #####! (FAQ #100360) When an element is configured as Integer with the format ##### (without dot) the value of the register is wrongly displayed on the terminal. This is a FW bug in the actual version of the PCD3.M_ and PCD2.M480. This problem occurs with all FW version up to: PCD3.M_ #13 (that means also 010, #11, #12) PCD2.M480 #23 (that means also 020, #21, #22) Solution Please
. Timings Display PCD7.D120 with a PCD3.M5xxx (FAQ #101569) The settings for Clock period High and Clock period low must be 2 / 150 same settings as for the PCD2.M [...] signal display CXG291M4N could be used. Introduction Due to a low demand, the delivery of PCD7.D120 displays will be discontinued in the year 2008 (last order: 31.09.2008). The repair
. Firmware compatibility PCD6.M3 and PCD6.M1/2 (FAQ #100147) PCD6.M3 PCD2.M1/M2 Ã [...] Ethernet module. However, as the PCD6 system has been discontinued, also the Ethernet module (PCD7.F651) for the PCD6 systems has been discontinued. To have an Ethernet TCP/IP port on a PCD, a PCD6.M3F650 had to be ordered (not possible any more). This version of the PCD6.M3 contains a PCD7.F651 module and has an Ethernet connector on the front plate instead of a D-Sub connector. It takes a single slot
