PG5 Version V 2.1.200 How to use the Conversion Fboxes to get a Temperature Curve Explanation and Database
The room template covers recently required HVAC room automation demands, like heating, cooling, FanCoil, presence detection. Beside this, the template is designed also to emulate a L60x room controller (partly), so a replacement of a L60x room controller by a freely programmable device can be done quite easy. The room template is dedicated to being used on PCD7.LRxx-P5 devices, but can be used on any other programmable device. In this case, some features must be removed or disabled, e.g. the SYLK Bus wall module (only available on PCD7.LRxx-P5) or the L60x emulation. The room
interrupt inputs (Int0 = i 8100; Int1 = i 8101) of a PCD2.M5xxx or PCD3.Mxxxx as normal input without using the corresponding interrupt XOB. Symptom When using I8100 or I8101 in Fupla they are [...] .ex. PCD2.W34, PCD2.W3x5, PCD2.W6x5 etc. some of these symbols are used by the F-Box. Other symbols in the project with the same names will cause a conflict. The error message above or similar will appear on [...] : PCD2.W340 Old Fbox NOT anymore supported., in Block: BL 425E2C0E, Page: 1, FBox: PCD2.W34 Reason This error is caused by a bug in the FBox library for the analogue modules. The
(PCD7.D776 Rev. 3) or by a hardware modification (PCD7.D776 Rev. 2). For updating the boot- and firmware version, please use the PCD8.D81W ( VTWIN) version 5.18 (or newer) which can be optained from [...] (port 0) of a PCD2.M110 (or a PCD2.M120) but not on the following systems: PCS1, PCD2.M150/M170/M480/M5xx0 or on a PCD3. Reason The PGU mode of recent PCD systems is no longer based on the P [...] .M150 and PCD2.M170: Modify your communication cable (Pin 6 should not be used, Pin 6 of PGU port =0). In the PCD program you need to add a "SASI Slave Mode D" with the parameters: RS 232, 9600, Parity, 7
PG5 2.3 licensing PG5 2.3, use the same licensing mode as on PG5 2.1 and PG5 2.2 There is a PG5 2.3 license file ‘USER.KEY' and there is a PG5 User Registration, file 'REGISTRATION.KEY'. PG5 2.3 needs a new ‘USER.KEY'. The ‘USER.KEY' file from PG5 2.2, PG5 2.1, PG5 2.0 or PG5 1.4 does not work on PG5 2.3. The same 'REGISTRATION.KEY' which was used in PG5 2.1 and PG5 2.2 can be used also in PG5 2.3. To use PG5 2.3 with a PG5 demo license, PG5 must contain a PG5 User Registration. If PG5 2.3 is used with a PG5 demo license and PG5 does not have a PG5 User Registration, then on first
PG5 2.3 licensing PG5 2.3, use the same licensing mode as on PG5 2.1 and PG5 2.2 There is a PG5 2.3 license file ‘USER.KEY' and there is a PG5 User Registration, file 'REGISTRATION.KEY'. PG5 2.3 needs a new ‘USER.KEY'. The ‘USER.KEY' file from PG5 2.2, PG5 2.1, PG5 2.0 or PG5 1.4 does not work on PG5 2.3. The same 'REGISTRATION.KEY' which was used in PG5 2.1 and PG5 2.2 can be used also in PG5 2.3. To use PG5 2.3 with a PG5 demo license, PG5 must contain a PG5 User Registration. If PG5 2.3 is used with a PG5 demo license and PG5 does not have a PG5 User Registration, then on first
PG5 2.3 licensing PG5 2.3, use the same licensing mode as on PG5 2.1 and PG5 2.2 There is a PG5 2.3 license file ‘USER.KEY' and there is a PG5 User Registration, file 'REGISTRATION.KEY'. PG5 2.3 needs a new ‘USER.KEY'. The ‘USER.KEY' file from PG5 2.2, PG5 2.1, PG5 2.0 or PG5 1.4 does not work on PG5 2.3. The same 'REGISTRATION.KEY' which was used in PG5 2.1 and PG5 2.2 can be used also in PG5 2.3. To use PG5 2.3 with a PG5 demo license, PG5 must contain a PG5 User Registration. If PG5 2.3 is used with a PG5 demo license and PG5 does not have a PG5 User Registration, then on first
.ch. On a PCD3.M6860 it’s possible to use BACnet on the Ethernet port ETH1 and/or on ETH2? (FAQ #102031) Yes it’s [...] one of the two Ethernet ports to avoid a bad behavior on BACnet. The activation and selection of the used Ethernet port for BACnet communication on the PCD3.M6860 is done in PG5 2.2 or PG5 2 [...] level Device Configurator: Support new IO modules - PCD2/3.W380 - PCD2.G200 - PCD7.W600 - PCD7.R610 Fupla Define groups and separators in the Page Navigator view Several
.ch. On a PCD3.M6860 it’s possible to use BACnet on the Ethernet port ETH1 and/or on ETH2? (FAQ #102031) Yes it’s [...] one of the two Ethernet ports to avoid a bad behavior on BACnet. The activation and selection of the used Ethernet port for BACnet communication on the PCD3.M6860 is done in PG5 2.2 or PG5 2 [...] level Device Configurator: Support new IO modules - PCD2/3.W380 - PCD2.G200 - PCD7.W600 - PCD7.R610 Fupla Define groups and separators in the Page Navigator view Several
.ch. On a PCD3.M6860 it’s possible to use BACnet on the Ethernet port ETH1 and/or on ETH2? (FAQ #102031) Yes it’s [...] one of the two Ethernet ports to avoid a bad behavior on BACnet. The activation and selection of the used Ethernet port for BACnet communication on the PCD3.M6860 is done in PG5 2.2 or PG5 2 [...] level Device Configurator: Support new IO modules - PCD2/3.W380 - PCD2.G200 - PCD7.W600 - PCD7.R610 Fupla Define groups and separators in the Page Navigator view Several
