auf e/a-Steckplatz 3 Batterie-Status in der Geschichte zeigt nicht PCD3.Mxxx0/PCD1.M2xx0: Einige Baudrates auf onboard Ports sind nicht korrekt PCD2.M4x60: RTC Lese-/Schreibzugriff sperren die PCD [...] Fehler zurück, da Port 1 nicht unterstützt wird PCD7. D443WT5R: Entfernen Sie e/a-Zugriff aus dem System. PCD geht jetzt HALT mit "INVALIDE OPCODE" PCD2. W220 mit Pt1000: signifikante Abweichung [...] Hardware-Revision Beschreibung und heißt "PCD2M5xx0_1.14.23(HW min D).blk" versehen. Also im Gegensatz zu den Dateinamen die Firmware 1.14.23 ist Rechtsstand zu PCD2.M5xx0 mit Hardware Revision 'A' und höher
. 32 GByte, 2 Ethernet, 1 RS-485, 1 socket for PCD7.F1xxS communication modules, 1 USB Device port for programming and service, 1 USB host, 1 CAN port (20a and 20b) 2 interrupt inputs, 1 watch dog relay, extendable up to 1023 I/O. I/O Extension for: Slot 4 to 7 PCD3.C200, Slot > 7 HPCD3.C100, HPCD3.C200 Supported PCD3 - I/O Modules: Supported PCD3 - I/O Modules: Starting with firmware 3.0.0: PCD3.Ax, PCD3.Ex, PCD3.W2x, PCD3.W3x, PCD3.W6x, PCD3.W745
Digital output module, 2 × 4 relays, 48 VAC/2 A or 50 VDC/2 A, 'make' contact, without contact protection
Digital output module, 2 x 3 relays, 250 VAC/2 A, 'make' contact, without contact protection
Aufgrund eines Fehlers auf der FW das Überlauf-Status-Flag der integrierten analogen Eingänge nicht ordnungsgemäß funktioniert. Dieses Flag wurde auf hoch in der Mitte der Messbereich eingestellt und
/improved No error message if fails to write backup file. e.g. when saving a file in the Common Files directory. Patch installer works also for W2k New features in PG5 Support of PCD3 Compact with [...] version 2.6.165. Symptom After having changed the operation mode of a PCD7.L60x Room controller from "autonomous" to "slave" the output values for the heating and cooling signal are not [...] replacing a DX system by a PCD without the need to replace all the XT extensions, too. Therefore the FBox library for the Johnson Controls JCI N2-Bus is designed to connect XT 9100 extension modules (where
/improved No error message if fails to write backup file. e.g. when saving a file in the Common Files directory. Patch installer works also for W2k New features in PG5 Support of PCD3 Compact with [...] version 2.6.165. Symptom After having changed the operation mode of a PCD7.L60x Room controller from "autonomous" to "slave" the output values for the heating and cooling signal are not [...] replacing a DX system by a PCD without the need to replace all the XT extensions, too. Therefore the FBox library for the Johnson Controls JCI N2-Bus is designed to connect XT 9100 extension modules (where
Procedure for updating the firmware of a PCD2.F2xx0 or PCD3.F2xx
level Device Configurator: Support new IO modules - PCD2/3.W380 - PCD2.G200 - PCD7.W600 - PCD7.R610 Fupla Define groups and separators in the Page Navigator view Several [...] following new features and modifications have been implemented in the patch 1 for PG5 2.1.200: Project Manager - RIO and device names can now begin with a digit - In the TCP/IP setting table, device is [...] with PG5 V2.1.200, but not back again Once a project has been opened with PG5 V2.1.200, it is not possible to open it again with the previous versions. As this new version contains no major changes
level Device Configurator: Support new IO modules - PCD2/3.W380 - PCD2.G200 - PCD7.W600 - PCD7.R610 Fupla Define groups and separators in the Page Navigator view Several [...] following new features and modifications have been implemented in the patch 1 for PG5 2.1.200: Project Manager - RIO and device names can now begin with a digit - In the TCP/IP setting table, device is [...] with PG5 V2.1.200, but not back again Once a project has been opened with PG5 V2.1.200, it is not possible to open it again with the previous versions. As this new version contains no major changes
