Important: This FAQ has been automatically translated by our software program. The original FAQ can be found here. SBC provides this information without liability for its correctness or functionality and does not assume liability being complete or correctly translated.

Niet alle vermeldingen van de geschiedenis kunnen worden gevonden in de Online Help van PG5

FAQ #100173

Sommige geschiedenis entries geïntroduceerd in nieuwe firmwareversies kunnen niet worden gevonden in de on line Help van de Debugger noch in de on line help van de Online Configurator.

Below you can find recently introduced History entries that can't be found in the Help files of PG5 versions older than PG5 1.3:

History Entry	Meaning	Remark
MEM-EXT. ERROR	Extension memory corrupted	Replaces "BAD TXT/DB TABLE"
CONFIG TOO LONG	HW setting to long to be put in EEPROM	Replaces "BAD MODEM STRING"
WATCHDOG FAIL	Restart due to SW Watchdog was executed
IPM NOT PRESENT	There is an IP configuration but no IP module
IPM DONT RESTART	PCD has restarted but the IP module does not respond
IPM HAS OLD FW	The IP module FW is not compatible with the PCD FW
IP FAIL SASITEXT	There is an error in the SASI text
IP FAIL SASI DBX	There is an error in the node list configuration DBX
IP FAIL NO IPM	An IP function has been carried out, but the PCD has no IP configuration
IP FAIL TOUT	Incorrect timeout value in Ether-S-Bus master SASI text
IP FAIL PORT Nbr	Incorrect port number in Ether-S-Bus master SASI text
Included text >3	Text nesting depth overflow
SBUS PGU Error	The SBUS PGU Port defined in the HW Settings isn't physically present

Error Messages concerning PCD1.M2, PCD2.M480, PCD2.M5xx0 and PCD3.Mxxx0 systems (SBC-NT)

History Entry	Meaning	.
Media corruption	This message indicates that the onboard RAM has been corrupted (becaused of a discharged superCap, bad Battery or similar). If this message is shown, all medias (R, C, F) are reset to 0, the clock is reset and the program is restored from the onboard flash (if possible). This entry has been replaced in firmware version 1.10.04 by "Memory Lost nn"
Memory Lost nn	Replacement message for "Media Corruption", but with more detailed informaton why the user program was restored and the media reset (since FW version 1.10.04): 01: Bad or missing battery 02: Supercap voltage too low 03: Corrupted memory pattern/signature 04: RAM memory cleared by user (push button) 05: RAM and flash memory cleared by push button 06: Corrupted program header
Not RUN on xx7HW	The HW is a xx/ type; the FW doesn't run the program on this HW
SYS. TYPE ERROR	The HW system type isn't correct
Reg>4095 not sup	The FW doesn't support more than 4095 registers
SF NOT LOADED	System function (CSF) isn't present
CSF INV PAR NBR	Invalide CSF parameter number
DOUBLE TIME BASE	Timebase defined more than once
XOB Nbr to big	XOB (Exception Organisation Block) number is too big
COB Nbr to big	COB (Cyclic Organisation Block) number is too big
FB Nbr to big	FB (Function Block) number is too big
PB Nbr to big	PB (Program Block) number is too big
IST Nbr to big	IST (Initial STep) number is too big
ST Nbr to big	ST (STep) number is too big
TR Nbr to big	TR (TRansition) number too big
SB Nbr to big	SB (Sequential Block) number too big
FABINFO CRC FAIL	Invalid CRC in the fabrication information. Please contact SBC
SYSWDOG START	Restart due to SW Watchdog executed
NO COB	No COB loaded
EXTHDR EEPR FAIL	Error in the EEPROM extended header
IP SB GWY FAIL	TCP/IP SBus gateway can't be initialised
IP Ch xxx no mem	No memory to open the channel on the TCP/IP Open data mode
MODEM: UART fail	UART doesn't accept the configuration
MODEM: Reset fail	Error on the modem reset command
MODEM: No modem	No modem or defective modem equipped on the port
MODEM: Init fail	Error on modem initialisation
MODEM: ERROR???	Unknown modem error
DIFF CFG Ch x	Different configuration on Profi-S-Net port x. Verify the configuration of the port
PS FAIL SASI DBX	Error in the node list configuration DBX
PS FAIL TOUT	Incorrect timeout value in Profi-S-Bus master SASI text
PS FAIL SAP	Incorrect SAP number in Profi-S-Bus master SASI text
PS FAIL SASITEXT	Error in SASI text
PSM NOT PRESENT	Profi-S-Net (Profibus) configuration but no Profi-S-Net (Profibus) existent
PSBus GWY FAIL	Profi-S-Bus GWY can't be initialized
PSBus PGU FAIL	Profi-S-Bus PGU port can't be initialized
SWTO ERROR	System Watchdog Timeout Error, see FAQ 100908 and 101069
BUS ERROR	Internal memory access failed. Please contact your local support team, see FAQ 101069
TCPS ERROR	TCPIP-Stack crash. Please contact your local support team
KRNL ERROR	Internal task overload. Please contact your local support team, see 101069
BACnet incompatible FW	The BACnet firmware found on the PCDx.R56x module is not compatible with the PCD firmware. Please update the BACnet firmware (see FAQ: 101010) This message is only given with firmware version 1.10.16 and later.
Bnt FAIL TL00001	An error occurred in relation to the BACnet configuration. Please refer to FAQ 101436.
MANUAL HALT	Indication that the PCD has been halted by pushing the Run/Halt button (implemented in firmware 1.14.23 and later)
EXT DEVICE FAIL	This message can be generated by PCD systems with FW 1.10.xx; The message is wrong and should be "31 CALL LEVELS". It indicates a too big nesting level of FB/PBs (if XOB 10 is programmed, it is called in this case)
RESISTERS FAIL	The termination resistors of port 3 of a PCD3.M5340 can not be activated due to a firmware restriction, see FAQ 101722.
INVALID PERI DBX	Hardware configuration contains errors (e.g. peripheral addresses, modules not supported by the firmware)

Related FAQs:

Niet alle vermeldingen van de geschiedenis kunnen worden gevonden in de Online Help van PG5

FAQ #100173

Categories