Your search returned 639 results

611. What state do the outputs of a PCD3.T760 have on bus failure?

     Relevance:

      

     6%

     By default, the outputs of a the modules mounted on a PCD3.T360 RIO will be reset on bus failure (or if the master is in STOP or HALT). This is the general defualt behaviour on Profubus DP networks that was overtaken for the Profi S-I/O networks.

612. When do I have to use the "SASI S-Bus Extended" FBox?

     Relevance:

      

     28%

     In the most cases the "Sasi ..." FBox can be used (which is recommended due to the fewer possibilities for wrong configuration). However, there are some specific reasons for using the FBox "Sasi S-Bus extended"

613. Why after the change of a PCD6.R210 memory support module in a PCD6 installation, the program does no more work correctly in the PCD6?

     Relevance:

      

     14%

     The PCD6.R210 module is a support module for the PCD6.R600 memory module. The PCD6.R600 does contain the PCD program but does not contain the S-Bus station number of the PCD. Therefore if the PCD6.R600 module is put in to a new PCD6.R210 module, it’s necessary to write with PG3/PG4 or PG5 the S-Bus station number to the PCD6.R210 module.

614. Why are broadcast telegramms not working anymore on the PCD3 or PCD2.M480

     Relevance:

      

     19%

     In firmware 03B and 03C an S-Bus broadcast telegram will block the communication interface until the next reboot of the PCD.

615. Why are the web-pages not loaded on the VGA MB panel (with Serial-S-Bus and less than 19200 kBit/s)? Which baudrate should be used for serial connections?

     Relevance:

      

     17%

     If the MB VGA panel is connected over serial line (RS232 or RS485) to a PCD and the baud rate is set to 9'600 Bit/s (or even less), the timeout on the MB VGA panel is to be adjusted to 500 ms.

616. Why can the PCD7.LRxx-P5 IRM room controller as S-Bus master, not read/write datas (inputs and outputs) from S-Bus slave devices via S-Bus?

     Relevance:

      

     45%

     The PCD7.LRxx-P5 IRM room controller can be operated on the RS485 interface as an S-Bus master. The PCD7.LRxx-P5 IRM room controller supports all S-Bus telegrams except the 2 telegrams: Read Input Write Output This means that it is not possible with the PCD7.LRxx-P5 IRM room controller, to read from the S-Bus Slave devices directly via S-Bus inputs and to write the outputs of the S-Bus Slave devices. If S-Bus Slave devices are used which use the S-Bus telegrams 'Read Input' and 'Write Output', then replace these devices with E-Line RIOs.

617. Why can't I change the Profi-S-Bus address on a PCD3.M6540 Port 2?

     Relevance:

      

     19%

     When using firmware version 1.08.23 the Profi S-Bus address can only be set one time on the PCD3.M6540 port 2.

618. Why can't I use the "alarming macro" on a VGA MB Panel with an S-Bus connection?

     Relevance:

      

     28%

     When trying to load the alarming macro with the VGA MB Panel (PCD7.D4xxV) through an S-Bus connection the microbrowser hangs and it is no more possible to browse the project.

619. Why can't my WebConnect find the SComm driver?

     Relevance:

      

     21%

     The SBC.Net WebConnect does provide an own driver for S-Bus Communication for most of the communicaiton methods (Ether-S-Bus, Serial-S-Bus and Profi-S-Bus). However, in some cases the SComm driver is required. This FAQ indicates where the WebConnect is looking for the drivers.

620. Why do I have communication problems with the PCD7.L1xx, 2xx, 3xx, 4xx when using the "S-BUS Station" F-Box?

     Relevance:

      

     14%

     This RIO modules need some time to synchronize the baudrate and establish communication.