for the user program is not reduced by configuring the "Extension Memory Backup size". See FAQ 101623 The S-Bus and IP configuration remain valid even if the user program is lost PG5 2.0.150 with [...] configuration, register, flags etc.). Please "upload all" before updating the firmware (for that you can "download all" after updating the firmware. Note that you'll need the USB port after the update (as your S-Bus [...] below. Note: In the attached example the data’s will be stored daily. If you store the data’s weekly or monthly you have to adapt the program especially the file name in the log file inside of
sub-distributors (E-Line housing) Routers for DIN rail mounting Modems, routers and network components for SBC S-Net Industrial Ethernet switchs Network components Ethernet TCP/IP (Ether-S-Net) Serial interface modules Pluggable in Saia PCD controllers Bus Termination - RS-485 Isolating DC/DC amplifiers: KFD11 and KFD12 Other
: Why isn't it possible to write to a PCD resource from a MB VGA panel (with S-Bus)? (FAQ #101123) If a S-Bus [...] VGA panel). Symptom If the connection between the PCD3 or a PCD2.M5xx0 (with firmware 1.09.38 or newer) and the MB VGA panel is realized with S-Bus (Serial S-Bus over RS232/RS485 or Ether S-Bus) and if the MB VGA panel (PCD7.D457Vxxx and PCD7.D410Vxxx) has installed the firmware (FW) 1.01.00 (or older) then it isn't possible writing a PCD variable from the MB VGA panel (edit box or
: Why isn't it possible to write to a PCD resource from a MB VGA panel (with S-Bus)? (FAQ #101123) If a S-Bus [...] VGA panel). Symptom If the connection between the PCD3 or a PCD2.M5xx0 (with firmware 1.09.38 or newer) and the MB VGA panel is realized with S-Bus (Serial S-Bus over RS232/RS485 or Ether S-Bus) and if the MB VGA panel (PCD7.D457Vxxx and PCD7.D410Vxxx) has installed the firmware (FW) 1.01.00 (or older) then it isn't possible writing a PCD variable from the MB VGA panel (edit box or
: Why isn't it possible to write to a PCD resource from a MB VGA panel (with S-Bus)? (FAQ #101123) If a S-Bus [...] VGA panel). Symptom If the connection between the PCD3 or a PCD2.M5xx0 (with firmware 1.09.38 or newer) and the MB VGA panel is realized with S-Bus (Serial S-Bus over RS232/RS485 or Ether S-Bus) and if the MB VGA panel (PCD7.D457Vxxx and PCD7.D410Vxxx) has installed the firmware (FW) 1.01.00 (or older) then it isn't possible writing a PCD variable from the MB VGA panel (edit box or
Programmable E-Line input/output module for room automation supply 24 VAC/VDC - 8 digital inputs 24 VAC/VDC - 3 relay changeover 230 VAC / 30 VDC, 6 A, max. inrush current 15 A - 1 relay changeover 230 VAC / 30 VDC, 10 A, max. inrush current 65 A - 4 triac outputs 24 VCA/1A or 230 VAC/1 A - 4 analogue inputs 12 bits 0…10 V, ±10 V, 0(4)…20 mA, Pt/Ni 1000, NTC, 0…2500 Ohm, 0…7500 Ohm, 0…300 kOhm - 4 analogue outputs 12 bits, 0…10 V (3 mA max.) - 3 interfaces: RS-485 (S-Bus), USB & NFC (service)
Programmable E-Line input/output module for room automation with auxiliary RS-485 interface supply 24 VAC/VDC - 8 digital inputs 24 VAC/VDC - 3 relay changeover 230 VAC / 30 VDC, 6 A, max. inrush current 15 A - 1 relay changeover 230 VAC / 30 VDC, 10 A, max. inrush current 65 A - 4 triac outputs 24 VCA/1A or 230 VAC/1 A - 4 analogue inputs 12 bits 0…10 V, ±10 V, 0(4)…20 mA, Pt/Ni 1000, NTC, 0…2500 Ohm, 0…7500 Ohm, 0…300 kOhm - 4 analogue outputs 12 bits, 0…10 V (3 mA max.) - 4 interfaces: RS-485 (S-Bus), auxiliary RS-485, USB & NFC (service)
. If you use the default standby mode S-BUS PGU you have to choose full handshake. Normally the handshake is on default. Only in this special case you have to change it to full [...] while sending an S-Bus telegram (e.g. missing port assignation or invalid data array or media) Invalid mathematical operation (e.g. division by zero or value overflow after a multiplication) Index [...] the Online Debugger!). Hint: Also have an eye on the SASI FBoxes you used as well as on the HMI Settings tab. The port doesn't exist The SASI text isn't valid S-Bus support isn't enabled in
. If you use the default standby mode S-BUS PGU you have to choose full handshake. Normally the handshake is on default. Only in this special case you have to change it to full [...] while sending an S-Bus telegram (e.g. missing port assignation or invalid data array or media) Invalid mathematical operation (e.g. division by zero or value overflow after a multiplication) Index [...] the Online Debugger!). Hint: Also have an eye on the SASI FBoxes you used as well as on the HMI Settings tab. The port doesn't exist The SASI text isn't valid S-Bus support isn't enabled in
. If you use the default standby mode S-BUS PGU you have to choose full handshake. Normally the handshake is on default. Only in this special case you have to change it to full [...] while sending an S-Bus telegram (e.g. missing port assignation or invalid data array or media) Invalid mathematical operation (e.g. division by zero or value overflow after a multiplication) Index [...] the Online Debugger!). Hint: Also have an eye on the SASI FBoxes you used as well as on the HMI Settings tab. The port doesn't exist The SASI text isn't valid S-Bus support isn't enabled in
