Single-phase energy meters with integral serial S-Bus interface for direct measurement, 230 VAC - 50 Hz Main features: Single-phase energy meter, 230 VAC 50 Hz - Direct measurement up to 32 A - Display of active power, voltage and current - S-Bus Interface to query the data - Reactive power and cos? available through interface - Up to 254 meter can be connected to the S-Bus Interface - 7-digit display - Lead seal possible with cap as accessory - Accuracy class B according to EN50470-3, accuracy class 1 according to IEC62053-21
Single-phase energy meters with integral serial S-Bus interface for direct measurement, 230 VAC - 50 Hz Main features: Single-phase energy meter, 230 VAC 50 Hz - Direct measurement up to 32 A - Display of active power, voltage and current - S-Bus Interface to query the data - Reactive power and cos? available through interface - Up to 254 meter can be connected to the S-Bus Interface - 7-digit display - Lead seal possible with cap as accessory - Accuracy class B according to EN50470-3, accuracy class 1 according to IEC62053-21 - according to MID directive
The default Timeout on Profi-S-Bus is baudrate related: Baudrate 9'600 Baud: 500 ms 93,75 kBaud: 500 ms 187,5 kBaud: 250 ms 500 kBaud: 250 ms 1,5 MBaud: 100 ms
In order to synchronize all PCD clocks on a network (Serial S-Bus, Profi-S-Bus or Ether-S-Bus) the FBox "Broadcast Clock" from the standard family "Communication" may be used. Depending on the range where the Broadcast message shall take effect the parameter "IP Node/Profi-S-Bus Address" has to be set correctly.
modified. The following IP-protocols are disabled by default on the deivce configurator of new PG5 projects: - S-Bus over TCP/IP - FTP - HTTP (Web-Server) PG5 projects made with precedent version [...] application program to a PCS 1 deletes the S-Bus settings on the PCS1 when PG5 2.1.420 is used. To solve the problem please check the following FAQ 101963 . Warning ' Licensed to: NOT [...] about 600MB of free space on your hard disk. Products not supported by PG5 2.1 The following products and protocols are not supported by PG5 2.1: PCD4 and PCD6 S-Bus RIO
modified. The following IP-protocols are disabled by default on the deivce configurator of new PG5 projects: - S-Bus over TCP/IP - FTP - HTTP (Web-Server) PG5 projects made with precedent version [...] application program to a PCS 1 deletes the S-Bus settings on the PCS1 when PG5 2.1.420 is used. To solve the problem please check the following FAQ 101963 . Warning ' Licensed to: NOT [...] about 600MB of free space on your hard disk. Products not supported by PG5 2.1 The following products and protocols are not supported by PG5 2.1: PCD4 and PCD6 S-Bus RIO
-protocols are disabled by default on the deivce configurator of new PG5 projects: - S-Bus over TCP/IP - FTP - HTTP (Web-Server) PG5 projects made with precedent version of PG5 2.1 are upward compatible [...] the S-Bus settings on the PCS1 when PG5 2.1.420 is used. To solve the problem please check the following FAQ 101963 . Warning ' Licensed to: NOT REGISTERED' is shown if a program is [...] . Products not supported by PG5 2.1 The following products and protocols are not supported by PG5 2.1: PCD4 and PCD6 S-Bus RIO (used with PCD1.T240) Profibus FMS For existing projects which
In seltenen Fällen ist die Ether-S-Bus Kommunikation bei Programmen die aus PG5 2.0 oder 2.1.200 in die PG5 2.1.210 importiert wurden nach einem Rebuild All und anschließendem Download nicht mehr in Funktion
If a S-Bus communication is used between the PCD3 or PCD2.M5xx0 and the MB VGA panel (PCD7.D457Vxxx and PCD7.D410Vxxx) then it may not be possible to write to the PCD variables (depending of the firmware installed on the MB VGA panel).
Analysing Serial-S-Bus communication can be done in several ways, depending on the focus of analysis (what shall be analysed; the telegrams on the wire, the requests sent by a PC software or the signal levels of e.g. Rx/Tx).
