interrupt inputs (Int0 = i 8100; Int1 = i 8101) of a PCD2.M5xxx or PCD3.Mxxxx as normal input without using the corresponding interrupt XOB. Symptom When using I8100 or I8101 in Fupla they are [...] Ymax - Range Example: the sensor gives 4...20 mA and we want to display a value from 0...500 m3 using a PCD4.W300 card! Range = (500- 0) . 20 mA = 625 [...] .ex. PCD2.W34, PCD2.W3x5, PCD2.W6x5 etc. some of these symbols are used by the F-Box. Other symbols in the project with the same names will cause a conflict. The error message above or similar will appear on
connected to PCD3.Mxxx or PCD2.M480 PLC's over Profi S-Bus, the terminal loses the communication after some time and get even frozen. This problem is corrected in the new boot, FW and driver. The PCD8.D81 V 5.09 is needed , the attached files have to be copied in it (see procedure below). It is also necessary to update the PCD3.Mxxx and PCD2.M480 FW with the version PCD3.Mxxx_023.blk / PCD2.M480_$27 or [...] 01 0271 0022 fexible cable Note: If the bautrates isn't greater than 187,5 bautes (for ex. Profi S-Bus with PCD3.M3xx / PCD7.D7xx) you can use other more advantegeous cable, especially
the PCD7.F7500. As result, the module can not be configured and the Error LED of the PCD is lit. The PCD2.M5540 hardware version C with modification 3,5, 6 contains a modification of the CPLD which assures that the module PCD7.F7500 it detected correctly. Solution Please use the PCD7.F7500 module wiith a PCD2.M5540 with the hardware version/modification "C 3,5, 6 ". In case you are concerned [...] Profibus DP interface (or Profi-S-I/O) interface is depending on the system (the amount is not the same for a PCD7.F750 or a PCD3). PCD7.F750 placed on a PCD2.M1x0 (non SBC-NT) The Profibus DP
the PCD7.F7500. As result, the module can not be configured and the Error LED of the PCD is lit. The PCD2.M5540 hardware version C with modification 3,5, 6 contains a modification of the CPLD which assures that the module PCD7.F7500 it detected correctly. Solution Please use the PCD7.F7500 module wiith a PCD2.M5540 with the hardware version/modification "C 3,5, 6 ". In case you are concerned [...] Profibus DP interface (or Profi-S-I/O) interface is depending on the system (the amount is not the same for a PCD7.F750 or a PCD3). PCD7.F750 placed on a PCD2.M1x0 (non SBC-NT) The Profibus DP
the PCD7.F7500. As result, the module can not be configured and the Error LED of the PCD is lit. The PCD2.M5540 hardware version C with modification 3,5, 6 contains a modification of the CPLD which assures that the module PCD7.F7500 it detected correctly. Solution Please use the PCD7.F7500 module wiith a PCD2.M5540 with the hardware version/modification "C 3,5, 6 ". In case you are concerned [...] Profibus DP interface (or Profi-S-I/O) interface is depending on the system (the amount is not the same for a PCD7.F750 or a PCD3). PCD7.F750 placed on a PCD2.M1x0 (non SBC-NT) The Profibus DP
. PCD3.M5360: Power CPU with 2MByte program memory, 128MByte intflash, USB, Ethernet, RS-232, 4 IO slots, expandable up to 64 IO modules. Fupla: Status indicators of unconnected FBox [...] .ch. On a PCD3.M6860 it’s possible to use BACnet on the Ethernet port ETH1 and/or on ETH2? (FAQ #102031) Yes it’s possible to use BACnet on both ports ETH1 or ETH2 of the PCD3.M6860. In PG5 it’s possible to activate at the same time BACnet on ETH1 and ETH2 but we strongly recommend to use/activate BACnet only on
. PCD3.M5360: Power CPU with 2MByte program memory, 128MByte intflash, USB, Ethernet, RS-232, 4 IO slots, expandable up to 64 IO modules. Fupla: Status indicators of unconnected FBox [...] .ch. On a PCD3.M6860 it’s possible to use BACnet on the Ethernet port ETH1 and/or on ETH2? (FAQ #102031) Yes it’s possible to use BACnet on both ports ETH1 or ETH2 of the PCD3.M6860. In PG5 it’s possible to activate at the same time BACnet on ETH1 and ETH2 but we strongly recommend to use/activate BACnet only on
. PCD3.M5360: Power CPU with 2MByte program memory, 128MByte intflash, USB, Ethernet, RS-232, 4 IO slots, expandable up to 64 IO modules. Fupla: Status indicators of unconnected FBox [...] .ch. On a PCD3.M6860 it’s possible to use BACnet on the Ethernet port ETH1 and/or on ETH2? (FAQ #102031) Yes it’s possible to use BACnet on both ports ETH1 or ETH2 of the PCD3.M6860. In PG5 it’s possible to activate at the same time BACnet on ETH1 and ETH2 but we strongly recommend to use/activate BACnet only on
. PCD3.M5360: Power CPU with 2MByte program memory, 128MByte intflash, USB, Ethernet, RS-232, 4 IO slots, expandable up to 64 IO modules. Fupla: Status indicators of unconnected FBox [...] .ch. On a PCD3.M6860 it’s possible to use BACnet on the Ethernet port ETH1 and/or on ETH2? (FAQ #102031) Yes it’s possible to use BACnet on both ports ETH1 or ETH2 of the PCD3.M6860. In PG5 it’s possible to activate at the same time BACnet on ETH1 and ETH2 but we strongly recommend to use/activate BACnet only on
. PCD3.M5360: Power CPU with 2MByte program memory, 128MByte intflash, USB, Ethernet, RS-232, 4 IO slots, expandable up to 64 IO modules. Fupla: Status indicators of unconnected FBox [...] .ch. On a PCD3.M6860 it’s possible to use BACnet on the Ethernet port ETH1 and/or on ETH2? (FAQ #102031) Yes it’s possible to use BACnet on both ports ETH1 or ETH2 of the PCD3.M6860. In PG5 it’s possible to activate at the same time BACnet on ETH1 and ETH2 but we strongly recommend to use/activate BACnet only on
