itselfs influences the measurement it has been stated that the precisision is not according to the manual of this PCD7.D290 display (26/841 version 4). The chapters 4.2.3 (Temperature sensor) and 4.2.4 (R.H. sensor) will be adapted accordingly in the next release. 4.2.3 Temperature sensor Temperature sensor used in PCD7.D290 is active and supplies as output a voltage of 10.0 mV/°C; this [...] Product Category HMI Text Terminal PCD7.D290 General
COSinus FW 1.24.69 was introduced into production for the systems PCD2.M5xx0, PCD3.Mxxx0. The corresponding BACnet and LonIP firmware is available on the support homepage. In March 2017 the COSinus FW 1.24.67 was introduced into production for the systems PCD2.M5xx0, PCD3.Mxxx0. The corresponding BACnet and LonIP firmware is available on the support homepage. In Mai 2015 the maintenance COSinus FW 1.24.30 was published for the systems PCD1.M0xx0, PCD1.M2xx0, PCD2.M5xx0, PCD3.Mxxx0, PCD3.Mxx60 and PCD7.D4xxxT5F. In February 2015 the COSinus FW 1.24.25 was introduced into
On a Profi S-Bus network when PCD7.D76_ terminals are connected to PCD3.Mxxx or PCD2.M480 PLC's over Profi S-Bus, the terminal loses the communication after some time and get even frozen. This problem is corrected in the new boot, FW and driver. The PCD8.D81 V 5.09 is needed , the attached files have to be copied in it (see procedure below). It is also necessary to update the PCD3.Mxxx and PCD2.M480 FW with the version PCD3.Mxxx_023.blk / PCD2.M480_$27 or newer! Ask the PCD technical support or your representation for it!
are connected to PCD3.Mxxx or PCD2.M480 PLC's over Profi S-Bus, the terminal loses the communication after some time and get even frozen. This problem is corrected in the new boot, FW and driver. The PCD8.D81 V 5.09 is needed , the attached files have to be copied in it (see procedure below). It is also necessary to update the PCD3.Mxxx and PCD2.M480 FW with the version PCD3.Mxxx_023.blk / PCD2.M [...] OS do not allow the access to COM-ports in the way which is used for DOS. Use an operating system which is based on DOS (DOS, WIN 3.11, Windows 95 or Windows 98) instead. PCD7.D8 is a
01 0271 0022 fexible cable Note: If the bautrates isn't greater than 187,5 bautes (for ex. Profi S-Bus with PCD3.M3xx / PCD7.D7xx) you can use other more advantegeous cable, especially [...] 7.T160 D-Sub 9pin on PCD Port 2 on PCD3.M3 and M6 A=RxD /TxD-N green D pin 8 D B=RxD /TxD-P red D/ pin 3 /D Example for the port 3 of the PCD3.M5540 as Serial-S-Bus RS485 connection (Serial-S-Bus) between PCD3.M5540 port 3 (S-Net D-Sub used as RS485 Serial-S-Bus) and PCD2.M5540 port 2 (connector block X3
work on port 2 on PCD3.M3x60 & PCD3.M5360. PCD3.M6860: Ping request from over rooter from different sub net is not respond. PCD3.M6860/M880: Profibus/S-IO/Profi-SBus does not work stable. PCD3.M [...] 2220-C15 Support of PCD2.M4x60 Support of PCD3.M3160/PCD3.M3360/PCD3.M5360 Support of PCD3.M6880, PCD3.T668 Standby-CPU-System Improvements PCD2.M4x6x, support Interrupt when reaching the [...] COSinus FW 1.28.37 was released as maintenance version for the systems: - PCD1.M0xx0/M2xx0, PCD2.M4x60, PCD3.Mxx60, PCD3.M6880 and PCD3.T665/T666/T668 . In June 2017: the COSinus FW 1
speed of the PCD7-L60x-1 Example: If the register has the value: ‘30’ then the maximum speed would be 3 and the minimum speed 0 ‘22’ then the maximum speed would be 2 and the minimum speed 2 -> the [...] . Which inputs values needs the FBox 'Man AO' (L60x-1 Man AO) to control the Y3/Y4/PWMs outputs on a PCD7.L60x-1 controller? (FAQ #101837) [...] FBox family 'RoomControler PCD7_60x V2' does need to have a decimal value without decimal point. (for an output value of 8.3 V the decimal value 83 have to be set) This FBox allows the manual
speed of the PCD7-L60x-1 Example: If the register has the value: ‘30’ then the maximum speed would be 3 and the minimum speed 0 ‘22’ then the maximum speed would be 2 and the minimum speed 2 -> the [...] . Which inputs values needs the FBox 'Man AO' (L60x-1 Man AO) to control the Y3/Y4/PWMs outputs on a PCD7.L60x-1 controller? (FAQ #101837) [...] FBox family 'RoomControler PCD7_60x V2' does need to have a decimal value without decimal point. (for an output value of 8.3 V the decimal value 83 have to be set) This FBox allows the manual
speed of the PCD7-L60x-1 Example: If the register has the value: ‘30’ then the maximum speed would be 3 and the minimum speed 0 ‘22’ then the maximum speed would be 2 and the minimum speed 2 -> the [...] . Which inputs values needs the FBox 'Man AO' (L60x-1 Man AO) to control the Y3/Y4/PWMs outputs on a PCD7.L60x-1 controller? (FAQ #101837) [...] FBox family 'RoomControler PCD7_60x V2' does need to have a decimal value without decimal point. (for an output value of 8.3 V the decimal value 83 have to be set) This FBox allows the manual
speed of the PCD7-L60x-1 Example: If the register has the value: ‘30’ then the maximum speed would be 3 and the minimum speed 0 ‘22’ then the maximum speed would be 2 and the minimum speed 2 -> the [...] . Which inputs values needs the FBox 'Man AO' (L60x-1 Man AO) to control the Y3/Y4/PWMs outputs on a PCD7.L60x-1 controller? (FAQ #101837) [...] FBox family 'RoomControler PCD7_60x V2' does need to have a decimal value without decimal point. (for an output value of 8.3 V the decimal value 83 have to be set) This FBox allows the manual
