Your search returned 698 results

321. Documents for Saia PCD QronoX

     Relevance:

      

     1%

     Documents Documents for Saia PCD QronoX General FAQ Documents concerning the IEC controller PCD3.M6893 Programmable with the Saia PCD® QronoX Engineering and Commissioning Suite. CPU LIOs Communication Modules I/O modules

322. BIM - Analogue output modules - 8 bits

     Relevance:

      

     1%

     Input/output modules for Saia PCD3 controllers Analogue output module, 4 channels, 8 bits, 0…10 V / 0…20 mA / 4...20 mA, jumper selectable (connector type A included)

323. Profibus

     Relevance:

      

     1%

     01 0271 0022 fexible cable Note: If the bautrates isn't greater than 187,5 bautes (for ex. Profi S-Bus with PCD3.M3xx / PCD7.D7xx) you can use other more advantegeous cable, especially [...] 7.T160 D-Sub 9pin on PCD Port 2 on PCD3.M3 and M6 A=RxD /TxD-N green D pin 8 D B=RxD /TxD-P red D/ pin 3 /D Example for the port 3 of the PCD3.M5540 as Serial-S-Bus RS485 connection (Serial-S-Bus) between PCD3.M5540 port 3 (S-Net D-Sub used as RS485 Serial-S-Bus) and PCD2.M5540 port 2 (connector block X3

324. PCD1.M137

     Relevance:

      

     1%

     ® COSinus-Systems PCD3.Mxxx0 and PCD2.M5xx0 - Texts < 4000 are writeable in runtime but PG5 recognizes if one of these texts has changed* - Texts >= 4000 are writeable in runtime PCD3.Mxx60 and PCD1.M2xx0 - Texts are configurable in the Build Options [...] 130, PCD1.M135, PCD2.M110, PCD2.M120 and PCD2.M150 The voltage of the battery is supervised. SBC advise to change the battery all 1 - 3 years. System with active battery supervision since

325. F2400: LON FTT10

     Relevance:

      

     1%

     exist the following module types to be plugged into PCD I/O slot 0..3: CPU Family LON TP/FT-10 with PCD2/3.F240x module PCD1.M2xx0 Supported from hardware version F PCD2.M5xx0 Supported from hardware version D PCD3.M3xx0 PCD3.M5xx0 PCD3.M6xx0 Supported from hardware version H PCD3.Mxx60 Supported [...] link With the following PCDs it is not possible to configure the FTT10 communication modul in the device configurator PCD2.M5xx0/PCD3.M3xx0/PCD3.M5xx0/PCD3.M6xx0. However you can use it, if you

326. F240: LON FTT10

     Relevance:

      

     1%

     exist the following module types to be plugged into PCD I/O slot 0..3: CPU Family LON TP/FT-10 with PCD2/3.F240x module PCD1.M2xx0 Supported from hardware version F PCD2.M5xx0 Supported from hardware version D PCD3.M3xx0 PCD3.M5xx0 PCD3.M6xx0 Supported from hardware version H PCD3.Mxx60 Supported [...] link With the following PCDs it is not possible to configure the FTT10 communication modul in the device configurator PCD2.M5xx0/PCD3.M3xx0/PCD3.M5xx0/PCD3.M6xx0. However you can use it, if you

327. M-Bus Master Module PCD2.F27x0 & PCD3.F27x

     Relevance:

      

     1%

328. What are the reasons for a "Bus Error" on a PCD2.M5 or a PCD3?

     Relevance:

      

     1%

     A "Bus Error" (which is indicated in the history of the PCD) indicates that the firmware was not able to execute an internal command (reading from the memory bus).

329. Why is the Profi S-Link cable not working on the PCD3 / PCD2.M480?

     Relevance:

      

     1%

330. Incompatibility of PCD2 /PCD3.F27x(0) and "Hydrometer M-Bus Receiver 868"

     Relevance:

      

     1%

     The M-Bus communication between the "Hydrometer M-Bus Receiver 868" (alternatively called "MB-Receiver") and the PCD2.F2710 has been analyzed and it was found that the device does not conform to the M-Bus specification (SN EN 13757-2). Therefore it can not be used together with the PCD2/3.F27x(0).