The PCD3.M6880 Standby Controllers are for creating redundant automation solutions, to ensure the uninterrupted operation of systems and processes.
If once the Software Watchdog is configured on a PCD2.M150, the system can't be started any more until the FW will be changed to either an older version (not recommended) or to the latest version 0E3 (recommended)!
interrupt inputs (Int0 = i 8100; Int1 = i 8101) of a PCD2.M5xxx or PCD3.Mxxxx as normal input without using the corresponding interrupt XOB. Symptom When using I8100 or I8101 in Fupla they are [...] Ymax - Range Example: the sensor gives 4...20 mA and we want to display a value from 0...500 m3 using a PCD4.W300 card! Range = (500- 0) . 20 mA = 625 [...] .ex. PCD2.W34, PCD2.W3x5, PCD2.W6x5 etc. some of these symbols are used by the F-Box. Other symbols in the project with the same names will cause a conflict. The error message above or similar will appear on
interrupt inputs (Int0 = i 8100; Int1 = i 8101) of a PCD2.M5xxx or PCD3.Mxxxx as normal input without using the corresponding interrupt XOB. Symptom When using I8100 or I8101 in Fupla they are [...] Ymax - Range Example: the sensor gives 4...20 mA and we want to display a value from 0...500 m3 using a PCD4.W300 card! Range = (500- 0) . 20 mA = 625 [...] .ex. PCD2.W34, PCD2.W3x5, PCD2.W6x5 etc. some of these symbols are used by the F-Box. Other symbols in the project with the same names will cause a conflict. The error message above or similar will appear on
interrupt inputs (Int0 = i 8100; Int1 = i 8101) of a PCD2.M5xxx or PCD3.Mxxxx as normal input without using the corresponding interrupt XOB. Symptom When using I8100 or I8101 in Fupla they are [...] Ymax - Range Example: the sensor gives 4...20 mA and we want to display a value from 0...500 m3 using a PCD4.W300 card! Range = (500- 0) . 20 mA = 625 [...] .ex. PCD2.W34, PCD2.W3x5, PCD2.W6x5 etc. some of these symbols are used by the F-Box. Other symbols in the project with the same names will cause a conflict. The error message above or similar will appear on
connected to PCD3.Mxxx or PCD2.M480 PLC's over Profi S-Bus, the terminal loses the communication after some time and get even frozen. This problem is corrected in the new boot, FW and driver. The PCD8.D81 V 5.09 is needed , the attached files have to be copied in it (see procedure below). It is also necessary to update the PCD3.Mxxx and PCD2.M480 FW with the version PCD3.Mxxx_023.blk / PCD2.M480_$27 or [...] 01 0271 0022 fexible cable Note: If the bautrates isn't greater than 187,5 bautes (for ex. Profi S-Bus with PCD3.M3xx / PCD7.D7xx) you can use other more advantegeous cable, especially
. PCD3.M5360: Power CPU with 2MByte program memory, 128MByte intflash, USB, Ethernet, RS-232, 4 IO slots, expandable up to 64 IO modules. Fupla: Status indicators of unconnected FBox [...] checkout our PCD3.M6893 (QronoX PCD), this PCD was developed for cybersecure applications. Information's can be found here . [...] ) On a PCD3.M6860 it’s possible to use BACnet on the Ethernet port ETH1 and/or on ETH2? (FAQ #102031) Yes it’s
. PCD3.M5360: Power CPU with 2MByte program memory, 128MByte intflash, USB, Ethernet, RS-232, 4 IO slots, expandable up to 64 IO modules. Fupla: Status indicators of unconnected FBox [...] checkout our PCD3.M6893 (QronoX PCD), this PCD was developed for cybersecure applications. Information's can be found here . [...] ) On a PCD3.M6860 it’s possible to use BACnet on the Ethernet port ETH1 and/or on ETH2? (FAQ #102031) Yes it’s
® COSinus PLCs (PCD1.M2, PCD2.M5, PCD3 but not on PCD2.M [...] .4.300 the S-Web Editor together with an example, the required FBoxes and firmware versions for PCD2.M5xx0 and PCD3.Mxxx0 can be downloaded from the support site from section Software --> PG5 --> PG5 1.4 --> [...] -Bus communication is used between the PCD3 or PCD2.M5xx0 and the MB VGA panel (PCD7.D457Vxxx and PCD7.D410Vxxx) then it may not be possible to write to the PCD variables (depending of the firmware installed on the MB
the PCD7.F7500. As result, the module can not be configured and the Error LED of the PCD is lit. The PCD2.M5540 hardware version C with modification 3,5, 6 contains a modification of the CPLD which assures that the module PCD7.F7500 it detected correctly. Solution Please use the PCD7.F7500 module wiith a PCD2.M5540 with the hardware version/modification "C 3,5, 6 ". In case you are concerned [...] Profibus DP interface (or Profi-S-I/O) interface is depending on the system (the amount is not the same for a PCD7.F750 or a PCD3). PCD7.F750 placed on a PCD2.M1x0 (non SBC-NT) The Profibus DP
