Due of an error in PG5 2.1.430 the symbol editor in Graftec does stop to work and does show the following error message: Solution: Do unzip the attached file and copy/overwrite the attached file ‘SRMDB52.dll’ to the PG5 installation folder: c:\Program Files\SBC\PG5 V2.1.430\ SRMDB52.dll New SRMDB52.dll has the version 2.1.430.1 old SRMDB52.dll which cause the problem is the version 2.1.430.0
floating point registers are not correctly detected (if PG5 2.0.210 or earlier is used). Instead of floats they are configured as integers. Reason The symbol files generated by PG5 2.0.210 (and [...] . Solution PG5 2.0.220 adds the indications again to the symbol files. If only an older version of PG5 2.0 can be used the following work-around could be applied: the configuration can be corrected [...] Possibility to export/import the header line on the export/import file. OPC Server version 2.02.17.20 (January 2014) New features Support of PG5 2.1.120 or later enhance the
files generated by PG5 2.0.210 (and earlier) are missing the indication to be a floating point register (a {F} in the comment of the symbol). As this indication is missing, the OPC Server can not figure out it is a floating point value. Solution PG5 2.0.220 adds the indications again to the symbol files. If only an older version of PG5 2.0 can be used the following work-around could be applied [...] Possibility to export/import the header line on the export/import file. OPC Server version 2.02.17.20 (January 2014) New features Support of PG5 2.1.120 or later enhance the
files generated by PG5 2.0.210 (and earlier) are missing the indication to be a floating point register (a {F} in the comment of the symbol). As this indication is missing, the OPC Server can not figure out it is a floating point value. Solution PG5 2.0.220 adds the indications again to the symbol files. If only an older version of PG5 2.0 can be used the following work-around could be applied [...] Possibility to export/import the header line on the export/import file. OPC Server version 2.02.17.20 (January 2014) New features Support of PG5 2.1.120 or later enhance the
range of 32. Therefore it is absolutely necessary to set the Base address to a multiple of 32. A Base address like e.g. 48 will cause problems [...] 5 Contols Suite). If a project was created with an older version of the programming tool, also the FB's provided with the older programming software were used. This may cause problems because of incompatibilities of the FB calls. To get around of this problem it is recommended to copy the used FBs directly into the CPU directory of the concerned project. This way the use of the correct FB version
range of 32. Therefore it is absolutely necessary to set the Base address to a multiple of 32. A Base address like e.g. 48 will cause problems [...] 5 Contols Suite). If a project was created with an older version of the programming tool, also the FB's provided with the older programming software were used. This may cause problems because of incompatibilities of the FB calls. To get around of this problem it is recommended to copy the used FBs directly into the CPU directory of the concerned project. This way the use of the correct FB version
is processed (only this page is part of the current Fupla file! If the Error isn't caused by this Fupla file, it will jump to any other page which doesn't cause the problem. Have a look at this page [...] while beeing online with the next Fupla file of the CPU). If you can't find the problem directly in a Fupla file, switch to the Online Debugger again. After having stopped, a line similar to the line [...] (or in case a PC is used, by interpreting the tracewin files). This phenomenon can be observed on PCD1.M1x5, PCD2.M150, PCD2/4.M170 and PCS1 systems (with firmware which are supporting the "Secure S
is processed (only this page is part of the current Fupla file! If the Error isn't caused by this Fupla file, it will jump to any other page which doesn't cause the problem. Have a look at this page [...] while beeing online with the next Fupla file of the CPU). If you can't find the problem directly in a Fupla file, switch to the Online Debugger again. After having stopped, a line similar to the line [...] (or in case a PC is used, by interpreting the tracewin files). This phenomenon can be observed on PCD1.M1x5, PCD2.M150, PCD2/4.M170 and PCS1 systems (with firmware which are supporting the "Secure S
Due to an error in the PG5 device template file of PG5 2.0.200 it’s not possible to switch on/off the digital outputs of the PCD3.compact CPUs. (PCD3.M2030V6, PCD3.M2130V6) Problem [...] 3.M2330A4T5) Problem Due to an error in the PG5 device template file of PG5 2.0.200 it isn't possible to switch on/off the relay outputs of the PCD3.WAC CPUs (PCD3.M2230A4T5, PCD3.M2330A4T1, PCD3.M2330A4T3, PCD [...] 3.T665/T666/T668: Enhancement for HTTP server to transparently support sending compressed files. Main corrections All PCD's SBUS parity mode, correction when NAK character is received as first byte of response
Due to an error in the PG5 device template file of PG5 2.0.200 it’s not possible to switch on/off the digital outputs of the PCD3.compact CPUs. (PCD3.M2030V6, PCD3.M2130V6) Problem [...] 3.M2330A4T5) Problem Due to an error in the PG5 device template file of PG5 2.0.200 it isn't possible to switch on/off the relay outputs of the PCD3.WAC CPUs (PCD3.M2230A4T5, PCD3.M2330A4T1, PCD3.M2330A4T3, PCD [...] 3.T665/T666/T668: Enhancement for HTTP server to transparently support sending compressed files. Main corrections All PCD's SBUS parity mode, correction when NAK character is received as first byte of response
