5. Problem The internal symbols of the PCD7.L60x FBox are missing. Normally they should be created automatically when the FBox is placed in a Fupla File Reason and Solution If this does not happen [...] correctly displayed: 20.6°C! This is only a visualisation probleme during the modifiation of the set point! Reason: Because over RJ9 protocol (used to communicate between the PCD [...] automaticaly. Possible problem: If the auto configuration option is activated during the powerup and the FBox Configuration isn't enable and the register ConfigTime Stamp (R=126) doesn
5. Problem The internal symbols of the PCD7.L60x FBox are missing. Normally they should be created automatically when the FBox is placed in a Fupla File Reason and Solution If this does not happen [...] correctly displayed: 20.6°C! This is only a visualisation probleme during the modifiation of the set point! Reason: Because over RJ9 protocol (used to communicate between the PCD [...] automaticaly. Possible problem: If the auto configuration option is activated during the powerup and the FBox Configuration isn't enable and the register ConfigTime Stamp (R=126) doesn
5. Problem The internal symbols of the PCD7.L60x FBox are missing. Normally they should be created automatically when the FBox is placed in a Fupla File Reason and Solution If this does not happen [...] correctly displayed: 20.6°C! This is only a visualisation probleme during the modifiation of the set point! Reason: Because over RJ9 protocol (used to communicate between the PCD [...] automaticaly. Possible problem: If the auto configuration option is activated during the powerup and the FBox Configuration isn't enable and the register ConfigTime Stamp (R=126) doesn
” after the function Network –>Test Reason In the FW 1.26.xx there is a problem with the file update on the Flash cards, the bindings are only updates in the memory but the [...] at least PG5 1.4.300 to configure your PCD2.M5xx0. EPLAN product macros, DWG and DXF files can be found here . Good to know When upgrading from firmware 1.10.xx or 1 [...] 2.M5540 show the history error message 'FABINFO CRC FAIL' or the entry 'Fab. Date (year/week): 2000/00; BAD PROD INFO CHECKSUM' in the diagnostic file and in the hardware info of the PG5 Online configurator
bigger (100-200MBytes). Problem The size of the project increase after storing to a really hughe size. Reason If unicode fonts are used which are not present in the PC [...] 't le possibility to use this version and you have the version 5.12 you can also add the new Fw in attachment. So, please execute the following steps: Download the files attached to this FAQ and unzip the archives. Copy the firmware files "VT155W.BIN" into the following folder: "C:\Program Files\SAIA\PCD8.D81W_512\\firmware\" Open the VTWIN project, compile it again and
On a Profi S-Bus network when PCD7.D76_ terminals are connected to PCD3.Mxxx or PCD2.M480 PLC's over Profi S-Bus, the terminal loses the communication after some time and get even frozen. This problem is corrected in the new boot, FW and driver. The PCD8.D81 V 5.09 is needed , the attached files have to be copied in it (see procedure below). It is also necessary to update the PCD3.Mxxx and PCD2.M480 FW with the version PCD3.Mxxx_023.blk / PCD2.M480_$27 or newer! Ask the PCD technical support or your representation for it!
as pure html files and not as 'java compatible files' and therefore the MB/pWeb panel isn’t able to display this sites. You have two possibilities to solve the problem: - set the setting order of [...] App Firmware 1.22.48 (March 2015) Main corrections FTP error due of username cgi access trough SBC.NET Solved problem when downloading .sprg file in PG5 with download [...] the PCD7.D443 MB Panel! (FAQ #101978) The 4.3’’ Room panel is using TrueType Font format: "xxxx.ttf files" , not
sent faster than with FW 001. Note that this only concernes programs written in IL which are not prepared to receive the characters quickly (or more than one per cycle) With the HMI Editor no problem [...] message "Error 31: C:\Program Files\SAIA-Burgess\PG5 1_4\Libs\Std\sfupdis5.srx: Line 323: Syntax error" is shown and the build fails. Reason The error message is shown because of an error on the SFup base library which is distributed with PG5 1.4.300. Solution To fix the error please install the library S-Fup Base Library version 2.6.100 or higher (installer file "S-Fup Base Library
page is part of the current Fupla file! If the Error isn't caused by this Fupla file, it will jump to any other page which doesn't cause the problem. Have a look at this page and the FBox with the [...] next Fupla file of the CPU). If you can't find the problem directly in a Fupla file, switch to the Online Debugger again. After having stopped, a line similar to the line written below will be shown [...] find the problem? (FAQ #100269) There is an Error Led on nearly every PCD system that can indicate a problem on the
page is part of the current Fupla file! If the Error isn't caused by this Fupla file, it will jump to any other page which doesn't cause the problem. Have a look at this page and the FBox with the [...] next Fupla file of the CPU). If you can't find the problem directly in a Fupla file, switch to the Online Debugger again. After having stopped, a line similar to the line written below will be shown [...] find the problem? (FAQ #100269) There is an Error Led on nearly every PCD system that can indicate a problem on the
