Your search returned 698 results

1. allowed Firmware for PCD3.M5540 hardware version D

   Relevance:

    

   1%

   the minimum firmware version for PCD3.M5540 hardware version D is V023

2. Wxxx-xx0

   Relevance:

    

   1%

   work on port 2 on PCD3.M3x60 & PCD3.M5360. PCD3.M6860: Ping request from over rooter from different sub net is not respond. PCD3.M6860/M880: Profibus/S-IO/Profi-SBus does not work stable. PCD3.M [...] 2220-C15 Support of PCD2.M4x60 Support of PCD3.M3160/PCD3.M3360/PCD3.M5360 Support of PCD3.M6880, PCD3.T668 Standby-CPU-System Improvements PCD2.M4x6x, support Interrupt when reaching the [...] COSinus FW 1.28.37 was released as maintenance version for the systems: - PCD1.M0xx0/M2xx0, PCD2.M4x60, PCD3.Mxx60, PCD3.M6880 and PCD3.T665/T666/T668 . In June 2017: the COSinus FW 1

3. Wxxx

   Relevance:

    

   0%

   A. Nevertheless it is possible measuring the range 0..20 mA with the analogue input modules for PCD systems. Why do the SBC input modules have a range of 0..20 mA? One advantage of measuring the [...] Product Category Archive Programmable Controller PCD6: CPUs in 19 inch racks Wxxx [...] commercially available products. PCD

4. Wxxx

   Relevance:

    

   0%

   A. Nevertheless it is possible measuring the range 0..20 mA with the analogue input modules for PCD systems. Why do the SBC input modules have a range of 0..20 mA? One advantage of measuring the [...] Product Index Archive PCD6 Wxxx General [...] . PCD6 Series (obsolete) Documentation

5. Why the status overflow flag of the onboard analogue inputs of the PCD1.M0, PCD1.M2, PCD3.M2x30V6 (PCD3 Compact) and PCD3.M2x30A4Tx (PCD3 WAC) does show an over-flow in the middle of the measurement?

   Relevance:

    

   2%

   Due of an error on the FW the overflow status flag of the onboard analogue inputs does not work correctly. This flag was set to high in the middle of the measurement range and not if the maximum valu

6. Why the MPI adapter doesn’t work on the MPI port of the PCD3.M5547, PCD3.M5567, PCD3.M5540, PCD3.M5440 or PCD3.5560?

   Relevance:

    

   2%

   The external MPI adapter which can be connected to the MPI Port of the PCD does need to be supplied with 24VDC. Depending of the hardware version of the PCD, on some FW this 24VDC supply on the MPI doesn’t work.

7. Why on a PCD3.M5/6xxx or a PCD2.M45xx the battery LED is switched on and the battery error message is activated in the application program after a new battery was inserted?

   Relevance:

    

   1%

   The battery voltage is checked in the battery module for undervoltage and overvoltage. New batteries have a too high voltage which causes the overvoltage limit to be exceeded.

8. Why it’s no more possible to set the PCD3.Mxx6x in the firmware download mode with the help of the run/stop switch?

   Relevance:

    

   1%

   On older PCD’s it was possible to set the PCD3.Mxx6x in to the firmware download mode by switching the run/stop switch (below the M1 memory slot) quickly several times during the start-up of the PCD. On newer PCD’s it’s no more possible to set the PCD in the firmware download mode with this procedure.

9. Why isn't it possible to write to a PCD resource from a MB VGA panel (with S-Bus)?

   Relevance:

    

   1%

   If a S-Bus communication is used between the PCD3 or PCD2.M5xx0 and the MB VGA panel (PCD7.D457Vxxx and PCD7.D410Vxxx) then it may not be possible to write to the PCD variables (depending of the firmware installed on the MB VGA panel).

10. Why is there an offset to the current PCD time in the alarming timestamp?

    Relevance:

     

    1%

    In case a BACnet firmware module has been installed on a PCD3.Mxxx0 or a PCD2.M5xx0 and a timezone has been configured, the time stamp of an S-Web alarm has an offset to the PCD time. There could be the same behaviour when you are using the SNTP (Simple Network Time Protocol).