connected to PCD3.Mxxx or PCD2.M480 PLC's over Profi S-Bus, the terminal loses the communication after some time and get even frozen. This problem is corrected in the new boot, FW and driver. The PCD8.D81 V 5.09 is needed , the attached files have to be copied in it (see procedure below). It is also necessary to update the PCD3.Mxxx and PCD2.M480 FW with the version PCD3.Mxxx_023.blk / PCD2.M480_$27 or [...] 01 0271 0022 fexible cable Note: If the bautrates isn't greater than 187,5 bautes (for ex. Profi S-Bus with PCD3.M3xx / PCD7.D7xx) you can use other more advantegeous cable, especially
connected to PCD3.Mxxx or PCD2.M480 PLC's over Profi S-Bus, the terminal loses the communication after some time and get even frozen. This problem is corrected in the new boot, FW and driver. The PCD8.D81 V 5.09 is needed , the attached files have to be copied in it (see procedure below). It is also necessary to update the PCD3.Mxxx and PCD2.M480 FW with the version PCD3.Mxxx_023.blk / PCD2.M480_$27 or [...] 01 0271 0022 fexible cable Note: If the bautrates isn't greater than 187,5 bautes (for ex. Profi S-Bus with PCD3.M3xx / PCD7.D7xx) you can use other more advantegeous cable, especially
connected to PCD3.Mxxx or PCD2.M480 PLC's over Profi S-Bus, the terminal loses the communication after some time and get even frozen. This problem is corrected in the new boot, FW and driver. The PCD8.D81 V 5.09 is needed , the attached files have to be copied in it (see procedure below). It is also necessary to update the PCD3.Mxxx and PCD2.M480 FW with the version PCD3.Mxxx_023.blk / PCD2.M480_$27 or [...] 01 0271 0022 fexible cable Note: If the bautrates isn't greater than 187,5 bautes (for ex. Profi S-Bus with PCD3.M3xx / PCD7.D7xx) you can use other more advantegeous cable, especially
Or "What is the difference between 0-, $- and #-firmware versions?". PCD firmware for non-Saia PCD® COSinus Systems (PCD1, PCD2.M1x0, PCD4, PCD6 and PCS) are named with 3 letters (e.g. 010, B0W or #31). This FAQ explains the meaning of these version and how to figure out which one is more recent.
The IL instruction DSP (display value on PCD7.F530 display) is not supported on Saia PCD® COSinus systems. When downloading it to a Saia PCD® COSinus system, the PCD will not go in RUN and give an error message such as "Invalid instruction" (e.g. a PCD2.M480), "Precompiler error" or "Invalid OPCODE" (on a PCD3.M5xx0 with firmware 1.10.16).
can be used in I/O slots 0 to 3 of PCD2.M5 or I/O slot 0 or 1 on a PCD2.M4 or PCD1.M2 [...] Product Category Programmable controller PCD3: CPUs, cassette design Fxxx: Comm modules F2xx: for I/O slot 0..3 F281: MP Bus [...] PCD2.F2xxx Serial communication modules to be placed in I/O slots 0..3
On older PCD’s it was possible to set the PCD3.Mxx6x in to the firmware download mode by switching the run/stop switch (below the M1 memory slot) quickly several times during the start-up of the PCD. On newer PCD’s it’s no more possible to set the PCD in the firmware download mode with this procedure.
If a S-Bus communication is used between the PCD3 or PCD2.M5xx0 and the MB VGA panel (PCD7.D457Vxxx and PCD7.D410Vxxx) then it may not be possible to write to the PCD variables (depending of the firmware installed on the MB VGA panel).
LonIp FW and coresponding PCD FW for PCD1.M2xx0, PCD2.M4x60, PCD3.Mxx60 Do use at least the PG5 firmware downloader version 2.1.311 or newer (included in PG5 patch 2.1.311 or newer) to prevent the loading of the FW 1.24.xx or 1.26.xx or newer to a not compatible PCD.
On a Profi S-Bus network when PCD7.D76_ terminals are connected to PCD3.Mxxx or PCD2.M480 PLC's over Profi S-Bus, the terminal loses the communication after some time and get even frozen. This problem is corrected in the new boot, FW and driver. The PCD8.D81 V 5.09 is needed , the attached files have to be copied in it (see procedure below). It is also necessary to update the PCD3.Mxxx and PCD2.M480 FW with the version PCD3.Mxxx_023.blk / PCD2.M480_$27 or newer! Ask the PCD technical support or your representation for it!
