Your search returned 817 results

751. Which inputs values needs the FBox 'Man AO' (L60x-1 Man AO) to control the Y3/Y4/PWMs outputs on a PCD7.L60x-1 controller?

     Relevance:

      

     6%

     On the PG5 HVC library, per default the values does have a dec.1 notation means that the 'raw' value 1234 does have a signification of 123,4. But the 'Man AO' FBox (L60x-1 Man AO) from the FBox family 'RoomControler PCD7_60x V2' does need to have a decimal value without decimal point. (for an output value of 8.3 V the decimal value 83 have to be set) This FBox allows the manual control of the Y3,Y4 or PWMs outputs (as long as there are not configured or used with HVC-Room FBox PCD7.L60x-1). If connected to the output of a HVC FBox, when the input value of the 'Man AO' FBox reaches 10

752. Why I get the error message "NAK response" during a program download (with PG5 SP2)?

     Relevance:

      

     34%

     On download of a big program with PG5 2.0.200 to a PCD1.M2xx0 or PCD3.Mxx60 the error message "Command not accepted: NAK response" can be returned by the downloader.

753. Why after a update to PG5 2.3.196 the web-pages are no more displayed on the PCD7.D5xxCF/CF1/RF panels?

     Relevance:

      

     10%

     Why after a update to PG5 2.3.196 the web-pages are no more displayed on the PCD7.D5xxCF/CF1/RF panels? Instead only a grey web-page is displayed.

754. Why after an download of a PG5 2.2.230 project to the PCD, where BACnet revision 14 is used, the application program on the PCD doesn’t work correctly and have a randomly unexpected/unwanted functionality?

     Relevance:

      

     14%

     Due to an error on the PG5 2.2.230 BACnet compiler, PCD resource addresses changes (Reg-ister/Flags/DB’s/Text address change of existing symbols) on existing PG5 projects are not detected from the PG5 BACnet compiler and therefore the changed PCD resource addresses are not taken in account in the PCD after the download of the modified program. Concerned products: All PCD’s with FW 1.28.xx or later where BACnet revision 14 is used and where modified PG5 2.2.230 projects are loaded to the PCD. The error doesn’t occur if: the PCD doesn’t contain a BACnet program. BACnet revision 9

755. Why are the inputs 8100 and 8101 continously "high" in my fupla file?

     Relevance:

      

     9%

     It is possible to use the interrupt inputs (Int0 = i 8100; Int1 = i 8101) of a PCD2.M5xxx or PCD3.Mxxxx as normal input without using the corresponding interrupt XOB.

756. Why are the static symbols missing during a Fupla page import (in PG5 2.0 SP2)?

     Relevance:

      

     13%

     When you try to import a previously exported Fupla page in PG5 2.0.200 then the static symbols aren't shown in the Symbol list window of the import dialog.

757. Why can't I add an extension module to my PCD3 compact?

     Relevance:

      

     8%

     In case a PG5 project has been created in PG 5 1.4.300 without patch 7 or later installed (or in a beta version of PG5 2.0, a $ version) the PCD3 compact was in pilot phase. At this time it wasn't possible adding an extension module (PCD3.Cxxx). In case this project is imported into PG5 2.0.110 the device configurator doesn't show the possibility to add an extension.

758. Why can't I build a Fupla containing the "EIB driver FT1.2" project with PG5 2.0.200?

     Relevance:

      

     27%

     When using the EIB/KNX driver FBox "EIB driver FT1.2" with PG5 2.0.200 (and the EIB FBox library SP2.6.210) the build of the project fails due to a fatal error.

759. Why can't I change the Profi-S-Bus address on a PCD3.M6540 Port 2?

     Relevance:

      

     10%

     When using firmware version 1.08.23 the Profi S-Bus address can only be set one time on the PCD3.M6540 port 2.

760. Why can't I connect a PCD2.M480 (with firmware 039) over the serial PGU port?

     Relevance:

      

     10%

     Due to a problem of the firmware version 039 the serial PGU connection on the PGU port does not work.