. PCD7.D1000 Embedded nano-browser (eDisplay for PCD2.M5xx0) Documentation Firmware Good to know There is a "Getting started with eDisplay" example available in the Getting Started section for PG5 2.0. For downloading the firmware of a PCD [...] /IP settings of the PCD2.M5 CPU with the eDisplay (PCD7.D3100E), when are the new TCP/IP settings are activated? (FAQ #101168)
.4 (R.H. sensor) will be adapted accordingly in the next release. 4.2.3 Temperature sensor Temperature sensor used in PCD7.D290 is active and supplies as output a voltage of 10.0 mV/°C; this [...] accuracy value: ± 1°C (± 1.5°C in the worse case) 4.2.4 R.H. sensor R.H. sensor used in PCD7.D290 is capacitive and supploes as output a capacity in the range 161.6 pF at 0% R.H. and 193.1 p [...] (PCD7.D23x and PCD7.D290) are connected to a RS 485 port (Bus terminal) of a PCDx.F2xx module, the communication doesn't work. Only one of the displays is available, the other one(s) is (are) not accessible
7.D23x are compatible with PG5 1.4.200. Symptom When programming a PCD with a PCD7.D23x (a pilot- or prototype version) with PG5 1.4.200, it may happen that the display jumps back to the root [...] protocol mode (RS485, "FTP" mode) on all PCD3 RS 485 ports (also on ports F2xx) must TEMPORARY be done with a special setting in the Advanced section of the SW Settings of the PG5. For the [...] When an element is configured as Integer with the format ##### (without dot) the value of the register is wrongly displayed on the terminal. This is a FW bug in the actual version of the PCD3.M_ and PCD2
. PCA programm update when replacing PCA2.D12 with PCD7.D120 (FAQ #100668) The attachment contains a program example for [...] the cut out is smaller than the D12, so if you have to replace an existing PCA2.D12 with a PCD7.D120, you have to use an adaptation frame for cut out 24.5 x 48.5 mm (type 4 108 4836 0) Features: The PCD7.D120 is a 6-digit LED display with decimal point; the PCA was 4-digit only Programming: The IL code and FBoxes for the PCA2.Dxx are not compatible with the PCD
compatible with the PCA2.Dxx: Mechanical: the dimension of the cut out is smaller than the D12, so if you have to replace an existing PCA2.D12 with a PCD7.D120, you have to use an adaptation frame for cut out 24.5 x 48.5 mm (type 4 108 4836 0) Features: The PCD7.D120 is a 6-digit LED display with decimal point; the PCA was 4-digit only Programming: The IL code and FBoxes for the PCA2 [...] Product Index Archive PCD7 Dxxx: HMI D120: 7 segment display
/IP settings of the PCD2.M5 CPU with the eDisplay (PCD7.D3100E), when are the new TCP/IP settings are activated? (FAQ #101168) The new TCP/IP settings are valid and activated as soon as the changing of the number is finished by pressing in the center of the joystick of the eDisplay. A restart or a power off/on of the PCD [...] Product Index PCD7 Dxxx: HMI D1000: room operating device General
PCD6.E100, PCD6.E610, PCD6.E611 or PCD6.A350 (FAQ #100264) These 4 digital I/O cards have all an address [...] . Nevertheless it is possible measuring the range 0..20 mA with the analogue input modules for PCD systems. Why do the SBC input modules have a range of 0..20 mA? One advantage of measuring the [...] the used power supply does not have the +/-15V the analogic carts can not work. With the PCD4/6.N200 supply it is not possible to use analogic cards. You will need the PCD4/6.N210 supply
PCD6.E100, PCD6.E610, PCD6.E611 or PCD6.A350 (FAQ #100264) These 4 digital I/O cards have all an address [...] . Nevertheless it is possible measuring the range 0..20 mA with the analogue input modules for PCD systems. Why do the SBC input modules have a range of 0..20 mA? One advantage of measuring the [...] the used power supply does not have the +/-15V the analogic carts can not work. With the PCD4/6.N200 supply it is not possible to use analogic cards. You will need the PCD4/6.N210 supply
a PCD2.M5xx0? (FAQ #101386) No, the PCD4.C225 is not supported by a PCD2.M5xx0 CPU. Due to the higher processing speed of the PCD2.M5 (compared to e.g. a PCD2.M150) it can not be guaranteed that the I/O modules are correctly accessed. Why is this fact not stated in the manual for the PCD4? In the manual for the PCD4 (27/734) there is not information regarding this restriction (it is only stated that a PCD2.M110 can not be used togheter with the PCD4.C225, and that no H-Modules or W1/W2/W3 modules
a PCD2.M5xx0? (FAQ #101386) No, the PCD4.C225 is not supported by a PCD2.M5xx0 CPU. Due to the higher processing speed of the PCD2.M5 (compared to e.g. a PCD2.M150) it can not be guaranteed that the I/O modules are correctly accessed. Why is this fact not stated in the manual for the PCD4? In the manual for the PCD4 (27/734) there is not information regarding this restriction (it is only stated that a PCD2.M110 can not be used togheter with the PCD4.C225, and that no H-Modules or W1/W2/W3 modules
