space for the new firmware features. The first PCD's were equipped with a 2 MB memory which was increased gradually. Using the hardware version number which can be red out online via PG5 over the [...] media (Flags, Registers, Timers/Counters) remains unchanged. However: Updating to FW 1.20.xx or higher from a version 1.16.xx deletes the data on SRAM. PCD2.M5xx0 & PCD [...] 5 firmware downloader version 2.1.311 or newer (included in PG5 patch 2.1.311 or newer) to prevent the loading of the FW 1.24.xx, 1.26.xx or newer to a not compatible PCD Firmware 1.28.51 (April 2022
space for the new firmware features. The first PCD's were equipped with a 2 MB memory which was increased gradually. Using the hardware version number which can be red out online via PG5 over the [...] media (Flags, Registers, Timers/Counters) remains unchanged. However: Updating to FW 1.20.xx or higher from a version 1.16.xx deletes the data on SRAM. PCD2.M5xx0 & PCD [...] 5 firmware downloader version 2.1.311 or newer (included in PG5 patch 2.1.311 or newer) to prevent the loading of the FW 1.24.xx, 1.26.xx or newer to a not compatible PCD Firmware 1.28.51 (April 2022
. Be aware that the PCD4.M170 is not equipped with the accu bloc. For this CPU a 3V Lithium battery Renata CR2032 (4 507 4817 0) is required PCA programm update when replacing PCA2.D12 with PCD7.D120 (FAQ #100668) The attachment contains a program example for [...] . PCA2.D12 Remote display (obsolete, replaced by PCD7.D120) Documentation
. Be aware that the PCD4.M170 is not equipped with the accu bloc. For this CPU a 3V Lithium battery Renata CR2032 (4 507 4817 0) is required PCA programm update when replacing PCA2.D12 with PCD7.D120 (FAQ #100668) The attachment contains a program example for [...] commercially available products. PCA2.D12 Remote display (obsolete, replaced by PCD7.D120) Documentation
. Be aware that the PCD4.M170 is not equipped with the accu bloc. For this CPU a 3V Lithium battery Renata CR2032 (4 507 4817 0) is required PCA programm update when replacing PCA2.D12 with PCD7.D120 (FAQ #100668) The attachment contains a program example for [...] . PCA series (obsolete, replaced by PCD series) Software Remember that the PCA series have been replaced by the PCD series quite a long time ago. As long as the parts stock lasts we
. Be aware that the PCD4.M170 is not equipped with the accu bloc. For this CPU a 3V Lithium battery Renata CR2032 (4 507 4817 0) is required PCA programm update when replacing PCA2.D12 with PCD7.D120 (FAQ #100668) The attachment contains a program example for [...] series have been replaced by the PCD series quite a long time ago. As long as the parts stock lasts we are repairing the units here in Murten, but it is getting more and more difficult to give support on
The PCD8.P100 has been discontinued in 2008 (repair service until end of 2013). For programming PCD controllers the software PG5 can be used together with e.g. a laptop. If you want to program PCD1.Mxxx, PCD2.M150/170, PCD4.M170 or PCD6.M300 you need the intermediate firmware version $301 since S-Bus is not supported by earlier versions. Contact your local SAIA sales company to get this firmware. For the use with PCD1 the use of a PCD8.K101 programming calbe is recommended since with a PCD8.K100 the relatively large inrush current of the P100 can cause the PCD1 to restart when connecting to
Yes it’s possible to use BACnet on both ports ETH1 or ETH2 of the PCD3.M6860. In PG5 it’s possible to activate at the same time BACnet on ETH1 and ETH2 but we strongly recommend to use/activate BACnet only on one of the two Ethernet ports to avoid a bad behavior on BACnet.
If the PCD2/3.W220Z18 card is plugged in to a ‘Power PCD‘ or a PCD2.C1000 or PCD2.C2000 and if all 8 analog inputs channels of the PCD2/3.W220Z18 module are connected to 8 PT100 sensors then the measured PT100 temperature values of the 8 channels are not correct. ‘Power PCD’s’ are: PCD1.M2x20, PCD1.M2160, PCD1.M2220-C15 PCD2.M5540, PCD2.M5440, PCD2.M4160, PCD2.M4560 PCD3.Mxx60 To solve the issue, use and connect only up to 7 PT100 sensors to the PCD2/3.W220Z18 or do use a PCD2/3.W350 module, if all 8 PT100 are needed.
Due of an error on PG5 2.1.200 it’s possible that on non NT Systems (PCS1, PCD1.M1xx, PCD2.M1xx) the Fupla online connections between F-Boxes does show a randomly status. That means that the connection between F-Boxes are set to 0/1 not as they should but in a randomly way. It’s possible that on the history there is also an error message ‘IR Overflow’ (Index Register Overflow)
